TyreON TL50E PRO 2 post lift - fully automatic elevador de 2 columnas nuevo

Capacity 5000 kg - fully automatic
Lifting height 11,6 - 195,5 cm
Vehicle length Very short to Multiple extended
Arms front 3-part : 82 - 170 cm
Arms back 3-part : 82 - 170 cm
Application Heavy duty professional
Construction 1075 kg
Between columns 320 cm
► 2.6 kW Electric hydraulic
► All-in-one 24V control unit
► Parking (lock) position every 5 cm
► Obstacle protection (slack cable)
► Low noise
► Vehicle width up to 283.8 cm
► Direct lowering(The lift does not first raise a bit)
C/w 2-stage lifting pads
Optional 6T base reinforcement kit (BFK6)
Voltage 400V
Promo - For Free Adapters 4 x 8 cm + 4 x 15,5 cm (HA8)
Promo - For Free Hand pump - lowering if power failure
Foundation 20 cm thick reinforced concrete C25/20
Certification CE / TÜV standard EN1493:2010
Packaging L290 x W55 x H95 cm - 1075 kg
Controller L45 x W27 x H27 cm - 10 kg
Powerunit L83 x W30 x H30 cm - 25 kg

HA8 set of plug-in height adapters
Hand pump, lowering if power failure
With 5.0 tons of lifting capacity and four 3-way telescopic lifting arms, a very wide range of vehicles can be lifted.
Intended for lifting small passenger cars such as Toyota IQ and Smart to multiple-extension commercial vehicles such as MB Sprinters, small rigids, large motorhomes and heavy commercial vehicles up to 283.8 cm wide.
In the factory safety test, the TyreON TL50E PRO has successfully been loaded dynamically up to 115% and statically up to 150% of the 5000 kg lifting capacity.
The vehicle lift is supplied optional with a 6000 kg base reinforcement kit that is mounted over the column foot plates.
Locks every 5 cm, much more safe than 5T and 6T 2 column lifts locking at only 2 height positions.
By the down button, the safety locks immediately retract and the lift immediately starts its descent. The 2 post lift does not raise a bit first.
TyreON TL50E
Due to the 1075 kg heavy construction, thick floor plates, automatic mechanical locking every 5 cm in both columns, this vehicle lift is suitable for heavy duty professional safe use.
Functionality
Fully automatic
Lift, lower, secure and unlock with buttons on the control panel
Direct automatic electric unlocking (the car does not rise a bit first)
Parking function with lock button on the control panel
The fully integrated hand pump allows precise adjustment of the lifting height for engine and transmission installations, exhaust, and much more.
4 lifting arms with aut-lock and auto-unlock
Hydraulic lifting system with two lifting cylinders (few moving parts)
Power transmission with heavy duty bar chains (also applied to forklifts)
Lifting mechanism with sliding blocks made of nano material, self-lubricating and maintenance-free
Easily accessible grease nipples
Large door protection rubbers
Plug-in 5.5 cm 2-stage adjustable lifting-pads for fast height adjustment
Lifting pads with anti-twist protection
Low noise aluminum industrial engine, thermally protected
Power unit with steel oil tank at the top of the column
3 cm threshold for cars with extremely low ground clearance
Comfortable working on vehicles with a high roof
1 year warranty on all parts
Practical holder for height adapters
Finished with powder coating
1 year warranty on all parts
Safety
CE certified - standard EN1493:2010
The controls and electrical circuit on the lift are 24 Volt
Steel synchronization cables equipped with slack cable protection
Safety mechanism with automatic activation every 5 cm
High stability thanks to specially designed lifting columns and column foot plates with small dimensions
Pressure relief valve on the power unit in case of an overweight vehicle
Broken hose protection, parachute valve on both cylinders
Limit switch and emergency stop
Hand pump for lowering in the event of a power failure
Foot protection on all lifting arms
A steel bracket guarantees the position of the chain on the pulley
Column floor plates with 8 mounting points er column
Optional 6000 kg base reinforcement kit with 6 extra mounting points per column
Vehicle length - Heavy duty professional use
TyreON TL50E 
TyreON presents the TL50E PRO 2 column vehicle lift with locking at every 5 cm, leaving old 5T and 6T 2 column lifts with locking at only 2 height positions far behind.
This new system is extremely safe and the lift can also be fixed at any height.
The four 3-part telescopic lifting arms have been developed for the new generation of (long) commercial vehicles.The front arms can be folded back completely.
The lift can be lowered from any height without having to press an UP button first.
With the down button the safety locks retract electromagnetically and the descent is starts immediately.
A situation of imbalance is automatically resolved by means of a system with synchronization cables
corrected, for example if a vehicle is much heavier on the driver's side than on the
passenger side.
The synchronization cables are provided with slack cable protection.
As a result, the vehicle lift will immediately stop the descent if an obstacle prevents the descent.
TyreON TL50E PRO heavy duty 2 post lift - fully automatic
TL50E PRO 2 post lift - supplied complete with
16 fixing anchor - 15 cm (16M20)
4 x lifting pad (2-stage adjustable)
Cabling and installation materials
Installation and operating manual with maintenance instructions
Hydraulic oil is not included - 10 Liter HV-ISO-32 is optional
Promo - For Free
TyreON HA8 set of solid plug-in height adapters (8)
Hand pump - lowering if power failure
NOTE: We recommend having the TyreON TL50E PRO two post car hoist installed by a specialized company.
TL50E PRO 2 post lift - fully automatic